BLUE NINA B1 EASY

1009 Views
- On-board Module: NINA-B1 Bluetooth 5.0 module
- Interfaces: SPI, GPIO, I2C, UART
- Voltage - Supply: 5V
- Board Size (mm): 28x39.5mm

View Detail

1. Introduction of  BLUE NINA B1 EASY (ATC-E21)

Giới thiệu Blue nina b1 easy

 

ATC-E21 Easy is a product designed by AT-COM to provide users with integrated facilities that are interconnected into a network through ATCBus.

The NINA-B1 series modules are small stand-alone Bluetooth® low energy modules featuring Bluetooth 5, a powerful Arm® Cortex®-M4 with FPU, and state-of-the-art power performance. The embedded low power crystal in NINA-B1 minimizes power consumption, thus extending the battery life.

2. Schematic

so do nguyen ly

3. Feature of BLUE NINA B1 EASY (ATC-E21)

Module ATC-E21

Module ATC-E21

Some feature of ATC-E21:

  • Bluetooth 5.0 band 2.4 GHz 40 channel.
  • Support extern Bluetooth antenna.
  • Default firmware is u-connect.
  • Led RGB displays module status.
  • Led displays power status.
  • Reset button.
  • 5V main power supply.
  • Size: 39.5 x 28 mm.

The ATCBus Socket integrate pins allows users to connect to products that supports ATCBus easily. All in one ATCBus.

ATCbus

Power Supply

Module B1 requires a clean and stable power supply. Main supply for ATC-E21 Easy via ATCBus at 2 pins 5V and GND. After that, the power IC TJ62FP30GSF of Tajin will be converted into 3.0V for B1 module. This power ensures up to 250mA response and pressure drop when the load does not exceed 400mV.

Logic level voltage selection

To communicate with external devices with logic 5V/3V, the board has an interface with 3.3V/5V logic voltage selection for user can choose depend their application. When manufacturing, the default logic voltage is 3.3V logic level

ATC-E21 uses bidirectional logic translator TXS0106EPW of Texas Instruments, it can use to convert logic level from 1.2~3.6V to 1.65~5.5V and bidirectional with speed up to 100Mbps. Logic level communicate of B1 is 1.8V and level logic of microcontroller normal is 3.3V/5V, so voltage translator IC need to use to compatible signal level

ATC-E21 supports UART to external device communicate with B1 module via AT command. UART interface supports baud rates from 2400 bps to 115.2 kbps and automatic baud rate detection. The default baud rates is 115200 kbps.

How to change the communication voltage:

  • Remove the 0R resistor at the unwanted position.
  • Solder the 0R resistor to the desired position of 3.3V or 5V.

Antenna Bluetooth

ATC-E21 hỗ trợ ăng-ten Bluetooth bên ngoài khi sử dụng B111

ATC-E21 supports external Bluetooth antenna when using B111

LED hiển thị

4. . Dimension

5. Video

Please enter correct your email
Content is your comment!
Content is too short to!
Comment is too long!
You can not continually write comments!

Related products

GPS MAX EASY

GPS MAX EASY

GPS MAX EASY is a compact solution for adding GPS functionality ...

OLED DISLAY EASY

OLED DISLAY EASY

OLED DISPLAY EASY carries a 128 x 64px blue monochrome ...

ARDUINO UNO EASY SHIELD

ARDUINO UNO EASY SHIELD

Arduino Uno Easy shield is an extension for Arduino ...